-
141
A YOLO11-Based Method for Segmenting Secondary Phases in Cu-Fe Alloy Microstructures
Published 2025-07-01“…With the development of industrialization, the demand for high-performance metal materials has increased, and copper and its alloys have been widely used. The microstructure of these materials significantly affects their performance. …”
Get full text
Article -
142
-
143
-
144
-
145
-
146
Impact of modified aggregate gradation on the workability, mechanical, microstructural and radiation shielding properties of recycled aggregate concrete
Published 2025-05-01“…Abstract The increasing need for sustainable construction practices has driven research into the utilization of recycled concrete aggregate (RCA) in new concrete mixes. …”
Get full text
Article -
147
Investigation of mechanical properties and microstructural characteristics of rice husk ash-based geopolymer mortar as patch repair
Published 2025-04-01“…The rapid expansion of the construction sector has escalated cement use, significantly impacting the environment due to CO2 emissions. …”
Get full text
Article -
148
Dynamic mechanical behavior of polypropylene fiber-reinforced shotcrete: Experimental analysis, microstructural observation, and numerical simulation
Published 2025-09-01“…Tunnel and underground engineering face safety risks such as collapses, rock bursts, and water inrushes during construction. Shotcrete is widely used for disaster mitigation due to its rapid application, simple process, and high early strength. …”
Get full text
Article -
149
Influence of water-repellent admixtures (Sitren and Stearate materials) on the microstructure and mechanical performance of conventional Portland cement paste and mortar
Published 2024-12-01“…Identifying the optimal mixture ratio for construction technology and effectively incorporating repellence features is a crucial aspect of this research.…”
Get full text
Article -
150
-
151
Use of hazardous barium slag as a supplementary cementitious material in calcium aluminate cement: Evolution of engineering properties and microstructure
Published 2025-07-01“…Microstructural analysis revealed that BS accelerated the hydration process and significantly altered hydration product compositions. …”
Get full text
Article -
152
Effect of boron content on the microstructure and magnetic properties of Ga-doped sintered Nd–Fe–B magnets
Published 2022-06-01“…The effect of boron content on phase formation, microstructure, and magnetic properties of the magnets was investigated. …”
Get full text
Article -
153
Durability and microstructure analysis of ultra-fine slag blended flyash-based self-compacting geopolymer concrete
Published 2025-01-01“…This study investigates the durability and microstructure of fly ash-based self-compacting geopolymer concrete (SCGC) enhanced with ultra-fine slag (UFS). …”
Get full text
Article -
154
High‐Yield, Cost‐Effective Fabrication of High‐Aspect‐Ratio Polyimide Microstructures for Robust Superhydrophobic Surfaces
Published 2025-05-01“…This approach achieves an exceptional yield rate of 99.8% and an aspect ratio of 10.7, enabling the construction of various microstructures. The SHS is demonstrated by fabricating microstructures on PI surfaces using the proposed method. …”
Get full text
Article -
155
Investigating the Effect of Tempering Temperature on the Microstructure, Hardness and Burst Pressure of 34CrMo4 Steel
Published 2025-04-01“…After going through the stages of the natural gas tank construction process and performing heat treatment, hardness testing, hydraulic pressure testing, burst pressure testing, and microstructural studies were performed to investigate the microstructural and mechanical properties of the produced tanks.Results: The results showed that in the annealing temperature range of 505 to 585°C, the hardness decreased from 392 to 310 Brinell and the breaking pressure decreased from 620 to 500 bar. …”
Get full text
Article -
156
-
157
Enhancing Concrete Strength and Microstructure with Basalt and Steel Fibers in Acid and Base Environments Incorporating Desert Sand
Published 2025-03-01“…Abstract Concrete is widely used in construction due to its remarkable compressive strength and durability. …”
Get full text
Article -
158
Ultrasound-Enhanced Friction Stir Welding of Aluminum Alloy 6082: Advancements in Mechanical Properties and Microstructural Refinement
Published 2024-10-01“…This study examines the effects of ultrasound-enhanced friction stir welding (USE-FSW) on the mechanical properties and microstructural characteristics of aluminum alloy AA6082-T6, commonly used in automotive, aerospace, and construction industries. …”
Get full text
Article -
159
-
160
