Geofluids Assessment of the Ayub and Shafa Hot Springs in Kopet-Dagh Zone (NE Iran): An Isotopic Geochemistry Approach by Hossein Mohammadzadeh, Majid Kazemi

“…It is very important to characterize the temperature and the depth of geothermal reservoirs. …”
Get full text

Theoretical and Experimental Study of Positive-Pressure Condensation Heat and Mass Transfer Processes in Bent-Tube Heat Exchangers by Jiaming Xing, Qing Cheng

“…By positive-pressure condensation, the dew point temperature can be increased, thereby increasing the cooling source temperature. …”
Get full text

Calculation of Heat of Adsorption of Gases and Refrigerants on Activated Carbons from Direct Measurements Fitted to the Dubinin–Astakhov Equation by Kandadai Srinivasan, Pradip Dutta, Kim Choon Ng, Bidyut Baran Saha

“…Because the adsorbed phase volume plays an important role, its dependence on temperature and pressure needs to be correctly assessed. …”
Get full text

Microstructure, Tensile Property, and Surface Quality of Glass Fiber-Reinforced Polypropylene Parts Molded by Rapid Heat Cycle Molding by Feng Liu, Taidong Li, Fuyu Xu, Jiquan Li, Shaofei Jiang

“…The tensile strength of RHCM parts reached the maximum at the mold heating temperature of 60°C. It is also observed that the surface gloss of the sample increases as the mold cavity surface temperature rises, and the increase of surface gloss decreases distinctly with the mold heating temperature higher than 90°C.…”
Get full text

Studi Experimental Terhadap Perpindahan Kalor Pada Tumbukan Multiple Droplets Dengan Variasi Frekuensi Tetesan by Indro Pranoto, Dannys Arif Kusuma, Teguh Wibowo, Fauzun Fauzun, Deendarlianto Deendarlianto, Indarto Indarto

“…The surface material of stainless steel with a temperature range of 120°C to 200°C was used in the study. …”
Get full text

Analysis of the Hybrid Power System for High-Altitude Unmanned Aircraft by Kangwen Sun, Ming Zhu, Lifeng Wang, Hu Liu

“…In the hybrid power system, a new electricity-generating method is adopted to spread the photovoltaic cell on the wing surface and arrange photothermal power in the wing box section. Because the temperature on the back of photovoltaic cell is high, it can be used as the high-temperature heat source. …”
Get full text

Separation of heavy metals using aqueous two-phase systems based on choline chloride/urea and betaine/urea deep eutectic solvents by Atefeh Sadeghi, Gholamreza R. Pazuki

“…Increasing the temperature, the concentration of metal and the amount of salt increased the extraction efficiency. …”
Get full text

Dynamic Behaviour Analysis of Turbocharger Rotor-Shaft System in Thermal Environment Based on Finite Element Method by Zhihao Liu, Renren Wang, Fang Cao, Pidong Shi

“…In this study, the dynamic behaviours of a rotor-shaft system with internal damping composite materials under the action of a temperature field are analysed. The temperature field will increase the tangential force generated by the internal damping of the composite material. …”
Get full text

Study on spontaneous combustion characteristics of coal under thermo mechanical coupling by Ji Wu, Zongxiang Li, Shuoran Huang, Cong Ding

“…Abstract The increase of coal seam mining depth leads to the increase of ground temperature stress, which affects the fracture development and spontaneous combustion characteristics of coal samples. …”
Get full text

The mediating effect of air pollution on the association between meteorological factors and influenza-like illness in China by Qinling Yan, Robert A. Cheke, Sanyi Tang

“…Results The meteorological factors minimum temperature/maximum humidity moderated by maximum humidity/minimum temperature and pressure directly affect ILI infections, and that some of meteorological factors can also indirectly affect them through air pollutants. …”
Get full text

Climate Change Impact on Photovoltaic Energy Output: The Case of Greece by Ioanna S. Panagea, Ioannis K. Tsanis, Aristeidis G. Koutroulis, Manolis G. Grillakis

“…The projected change in photovoltaic energy output was then estimated, considering changes in temperature and insolation. The spatiotemporal analysis indicates significant increase in mean annual temperature (up to 3.5°C) and mean total radiation (up to 5 W/m2) by 2100. …”
Get full text

Radiation balance and urban land use (case study: Kermanshah city) by taher Safarrad, mehran Mansourinia, hersh entezami

“…The results also indicated that these differences are due to changes in output energy (α and RL↑), and any change in land use over time will ultimately lead to a change in the radiation balance and the temperature of those places, which this temperature increase, is different from the increase of the temperature due to global warming.…”
Get full text

Study on Downhole Throttling Characteristics of High Water Content Gas by Jie Zheng, Zhenzhen Li, Yihua Dou, Yarong Zhang, Cheng Bi, Xu Yang, Jiahui Li

“…Combined with the downhole throttling mechanism and gas-liquid two-phase homogeneous flow theory, the temperature and pressure field distribution model is established. …”
Get full text

The Intramolecular Pressure and the Extension of the Critical Point’s Influence Zone on the Order Parameter by Jose Luis Rivera, Homero Nicanor-Guzman, Roberto Guerra-Gonzalez

“…The length of the critical influence zone is under debate because for some properties, like shear viscosity, the extension is only a few degrees, while for others, such as the density order parameter, the critical influence zone covers up to hundreds of degrees below the critical temperature. Here we show that, for ethane, the experimental critical influence zone covers a wide zone of tens of degrees (below the critical temperature) down to a transition temperature, at which the apparent critical influence zone vanishes, and the transition temperature can be predicted through a pressure analysis of the coexisting bulk liquid phase, using a simple molecular potential. …”
Get full text

Effects of Gd211 Particles Characteristic in the Precursor Pellets on the Levitation Force of Single-Domain GdBCO Bulks Prepared by the Gd + 011 TSIG Method by Xiaochun Yuan, Wanmin Yang

“…In this paper, single-domain GdBCO bulks have been fabricated by a new Gd + 011 TSIG method with precursor solid phase pellets (PSPPs) of different Gd211 particle sizes and distributions, prepared by solid state reaction with well-mixed (Gd2O3 + BaCuO2) pellets at different temperatures. The novel results indicated that (1) the average size of Gd211 particles in PSPP is monotonically increasing with increasing the sintering temperature up to 1200°C. (2) With increasing the sintering temperature from 950 to 1200°C, the porous ratio and the density of the PSPP are, respectively, monotonically decreasing and increasing. …”
Get full text

Bubble Flow Analysis of High Speed Cylindrical Roller Bearing under Fluid-Solid Thermal Coupling by Li Cui, Wenxia Wang, Zhang Yanlei

“…In comparison, the coupling effects on flow pressure and temperature are obvious. For a given rotating speed, there is an optimal value for air volume fraction, such that temperature rise of the bearing reaches the lowest value. …”
Get full text

Analysis of Koo-Kleinstreuer-Li model water-based nanofluid: Interval Type 2 fuzzy approach by M.M. Nayak, S.R. Mishra, Rupa Baithalu

“…Interval type-2 trapezoidal fuzzy sets are used in this fuzzy analysis to investigate the role of several physical factors on velocity and temperature distribution, shear rate, Nusselt number (rate of heat transfer), nanoparticle diameter, fluid temperature, and volume concentration. …”
Get full text

A review of thermographic techniques for damage investigation in composites by Laura Vergani, Chiara Colombo, Flavia Libonati

“…Thermography is the analysis of the surface temperature of a body by infrared rays detection via a thermal-camera. …”
Get full text

Optimization of Process Parameters for Vertical-Faced Polypropylene Bottle Injection Molding by Youmin Wang, Zhichao Yan, Xuejun Shan

“…For filling and maintaining pressure during the process of infusion bottle injection molding, the orthogonal test table L25 (56) using CAE was designed for injection molding of the bottle, with six parameters such as melt temperature, mold temperature, injection pressure, injection time, dwell pressure, and dwell time as orthogonal test factors. …”
Get full text

Synthesis and Optimization of 2,5-Dihydroxyterephthalic Acid in a Slurry Reactor by Reza Pirdadeh Beiranvand, Saeed Ovaysi

“…A fractional factorial design is used to screen four parameters including reactor pressure, temperature, catalyst-to-DSH molar ratio, and reaction time. …”
Get full text