Investigation on the Achievable Flow Length in Injection Moulding of Polymeric Materials with Dynamic Mould Tempering by Steve Meister, Dietmar Drummer

“…A higher mould temperature leads only to a slight increase in flow length. …”
Get full text

Research of the Robust Design of New Type of Disc Brake based on Uncertainty Theory by Sun Hong

“…Finally,the result of robust design analysis is verified by the analysis of braking distance and braking temperature. The results show that,through the calculation of the pareto solution set of braking distance and temperature and selecting a reasonable combination of μf,δf,the robust design model parameter can be obtained,the efficiency of design is greatly improved. …”
Get full text

Computational Fluid Dynamics for Cavity Natural Heat Convection: Numerical Analysis and Optimization in Greenhouse Application by Yin Zhang, Menglong Zhang, Jianwu Xiong, Gang Mao, Yicong Qi

“…Moreover, panel slope tilting angle (θ) highly determines inside heat transfer subregions in terms of the vertical temperature gradient declines with rising θ, improving the temperature distribution uniformity inside. …”
Get full text

Relationship of Meteorological and Air Pollution Parameters with Pneumonia in Elderly Patients by Suleyman Serdar Tasci, Cemil Kavalci, Afsin Emre Kayipmaz

“…Results. When the temperature was high and low, the number of days consulted due to pneumonia was related to low air temperature (p<0.05). …”
Get full text

Analysis of the Thermal Elastohydrodynamic Lubrication of Water-lubricated Hybrid Ceramic Bearing by Zhang Tonggang, Wang Youqiang, Xu Caihong, Wang Limei

“…The region where the local maximum temperature of lubricating film appeared under different working conditions is analyzed. …”
Get full text

Numerical Modeling of Thermal-Dependent Creep Behavior of Soft Clays under One-Dimensional Condition by Qi-Yin Zhu, Ping Qi

“…The paper focuses on investigating the influence of temperature on the time-dependent stress-strain evolution. …”
Get full text

Fire Resistance Investigation of Simple Supported RC Beams with Varying Reinforcement Configurations by Yamin Song, Chuanguo Fu, Shuting Liang, Ankang Yin, Longji Dang

“…One beam was treated as the control case of room temperature while the other five beams were exposed to high temperature. …”
Get full text

Fault Diagnosis Method for Bearing of High-Speed Train Based on Multitask Deep Learning by Jia Gu, Ming Huang

“…The model can judge whether the running train bearing temperature is in the normal range in real time and predict and alarm the abnormal bearing temperature.…”
Get full text

Thermal Tolerance in Anuran Embryos with Different Reproductive Modes: Relationship to Altitude by Manuel Hernando Bernal, John D. Lynch

“…Anurans are ectothermic animals very sensitive to temperature, mainly during the embryonic stage. In addition, environmental temperature decreases with altitude, and the amphibian fauna changes. …”
Get full text

Single-Event-Upset Sensitivity Analysis on Low-Swing Drivers by Nor Muzlifah Mahyuddin, Gordon Russell

“…It is found that, with temperature, there is no clear factor that can justify the direct impact of temperature on the SEU tolerance. …”
Get full text

An Efficient T-S Assimilation Strategy Based on the Developed Argo-Extending Algorithm by Chaojie Zhou, Xiaohua Ding, Jie Zhang, Jungang Yang, Qiang Ma

“…Considering the insufficiency of the observations, the performance of assimilation with few temperature and salinity (T-S) profiles is not satisfied. …”
Get full text

Thermal Elastohydrodynamic Lubrication Analysis of Bevel Gear based on a Finite Line Contact Model by Cong Wei, Youqiang Wang, Yabo Zhou, Shenwen Long

“…Among them， the oil film pressure of the small end is slightly larger than the oil film pressure of the big end， the oil film thickness of the small end is smaller than the oil film thickness of the big end， the temperature distribution difference along the tooth width direction is more obvious， and the temperature of the middle layer of the oil film is greater than the temperature of the two solid surfaces. …”
Get full text

Thermodynamic and Exergoeconomic Study of an Absorption-Compression Refrigeration Cycle Driven by a Geothermal Energy Resource by Armin Khazaei Nam, Asgar Minaei, Mohammad Ebadollahi, Hadi Ghaebi

“…The purpose of this system is to produce four different products: power, heating load, cooling, and fresh water. The effect of temperature and mass flow rate parameters of the geothermal source, fresh air ratio parameter, condenser temperature, evaporator-condenser outlet temperature of the absorption refrigeration section, and the evaporator temperature of the vapor compression refrigeration system on the essential decision variables of the system and also on the temperature provided for the thermal comfort of the house and The flow of fresh water produced by the fan coil unit is provided, which has the most influence on the decision parameters, is caused by the output temperature and mass flow rate of the geothermal energy source. …”
Get full text

Surface and interfacial properties of Fe-C-O-Cr alloys in contact with alumina by Novák V., Řeháčková L., Váňová P., Smetana B., Konečná K., Drozdová Ľ., Rosypalová S.

“…In this paper, temperature and concentration dependencies on density and surface tension of liquid Fe-C-O-Cr alloys (1.93 - 4.80 wt.% Cr) were investigated in high-temperature resistance observation furnace by a sessile drop method during heating from liquidus temperature to 1600°C. …”
Get full text

Pengaruh aplikasi edible coating gel lidah buaya (Aloe Vera L.) dengan penambahan carboxymethyl cellulose terhadap mutu buah melon (Cucumis Melo L.) potong by Rohula Utami, Alifa Sekar Jannah, Asri Nursiwi

“…The results showed a significant effect of adding various concentrations of CMC on increasing hardness, total soluble solids, pH, vitamin C content, and decreasing total plate count (TPC) of fresh-cut melon stored at room temperature and refrigerated temperature. Applying 1% and 1.5% CMC in aloe vera gel edible coating could maintain the fresh-cut melon quality compared to other treatments at room temperature and refrigerated temperature, respectively…”
Get full text

Study on Safety Performance of Building Finish Layer under Thermomechanical Coupling Condition by Kai Yan, Yansong Hu, Kaozhong Zhao, Xin Lin

“…The anchoring strength is influenced significantly by anchoring construction sequence and temperature. The stress under the coupled effect of temperature and load is greater than that of the single effect of load, and the stress distribution changes significantly. …”
Get full text

Derivation and Implementation of a Non‐Local Term to Improve the Oceanic Convection Representation Within the k–ɛ Parameterization by Alexandre Legay, Bruno Deremble, Hans Burchard

“…To do so, we extend the k–ε algebraic second‐moment closure by relaxing the assumption on the equilibrium of the temperature variance θ′2‾. With this additional evolution equation for the temperature variance, we obtain a k–ε–θ′2‾ model (the “kεt” model) which includes a non‐local term for the temperature flux. …”
Get full text

Production of Biochar by Pyrolysis of Food Waste Blends for Negative Carbon Dioxide Emission by Zsolt Dobó, Helga Kovács, Gábor Nagy

“…Additionally, higher pyrolysis temperature resulted in lower carbon capture potential within the temperature range utilized in this study. …”
Get full text

Investigation of Vortex Clouds and Droplet Sizes in Heated Water Spray Patterns Generated by Axisymmetric Full Cone Nozzles by M. Y. Naz, S. A. Sulaiman, B. Ariwahjoedi, Ku Zilati Ku Shaari

“…It was noticed that SMD varies slightly w.r.t. position when measured at room temperature whereas at higher temperature values, it became almost constant at distance of 55 mm downstream of the nozzle exit.…”
Get full text

Gas Storage Model of Residual Coal Adsorption in Abandoned Mine by San Zhao, Xiangjun Chen, Lin Wang, Lin Li

“…The results show that pressure has a positive effect on gas adsorption by residual coal, while temperature has a negative effect on it. The adsorption potential gradually decreases with increasing pressure and increases with increasing temperature, while the adsorption space increases with increasing pressure and decreases with increasing temperature. …”
Get full text