Flexural Capacity Calculation Approach for Precast Grouted Shear Wall Influenced by Joint Interface Displacements by Dong-yue Wu, Shu-ting Liang, Zheng-xing Guo, Xiao-jun Zhu

“…With excessively utilized confinement steels, connecting steels, and steel sleeves, their mechanical properties satisfied the strength requirements. …”
Get full text

Effect of pH on Escherichia coli Removal by Electrocoagulation and Elimination Kinetics after Treatment by A. C. Ndjomgoue-Yossa, C. P. Nanseu-Njiki, E. Ngameni

“…Under the experimental conditions used, more than 5 log removal of E. coli is obtained, irrespective of the nature of the electrode (ordinary steel or aluminum) and the value of the initial pH. …”
Get full text

Autarky and Material Contingencies in Italian Architectural Debate (1936-1954) by Pep Avilés

“…This soon translated in both a control of foreign currencies in order to purchase iron and steel on the international markets, and a vociferous campaign discouraging the use of materials that were demanded by the military endeavour. …”
Get full text

Study Analysis of Car Rim Design and Mechanical Properties Using Catia by Bayu Pranoto, Gunawan Chandra, Fakhruddin Muhammad, Trifiananto Muhammad, Purwanto

“…This study discusses the design of a car rim and analyzed its mechanical properties using three different basic materials: aluminum, steel, titanium. The purpose of this study is to reduce production time and to minimize the risk of design failure. …”
Get full text

An Experimental Investigation of Unbonded Laminated Elastomeric Bearings and the Seismic Evaluations of Highway Bridges with Tested Bearing Components by Gang Wu, Kehai Wang, Guanya Lu, Panpan Zhang

“…This paper presents an experimental program performed to investigate the behavioral characteristics of unbonded steel-reinforced laminated elastomeric bearings (U-SLEBs), which have been widely used for highway bridges in China. …”
Get full text

Efficacy of Esthetic Retainers: Clinical Comparison between Multistranded Wires and Direct-Bond Glass Fiber-Reinforced Composite Splints by Andrea Scribante, Maria Francesca Sfondrini, Simona Broggini, Marina D'Allocco, Paola Gandini

“…The purpose of this longitudinal prospective randomized study was to evaluate the reliability of two different types of orthodontic retainers in clinical use: a multistrand stainless steel wire and a polyethylene ribbon-reinforced resin composite. …”
Get full text

Experimental and numerical investigations of CFRP reinforced masonry ?beams performance under bending loads by Mahmoud Zaghlal, Alaa El-Sisi�, Mohamed Husain, Samar Samy

“…In this paper, an experimental and numerical study was achieved to investigate the behavior of masonry beams internally reinforced using carbon fiber-reinforced polymer (CFRP) and hybrid steel/CFRP reinforcements. Three beams were built using concrete bricks and grout mortar. …”
Get full text

Improve Efficiency of Photovoltaic/Thermal Systems using Porous Materials: An Experimental Study by H. Farzan

“…For this purpose, an experimental setup was fabricated, and two scenarios were investigated: a non-porous PV/T and a porous one in which steel wool was used as a porous material. The acquired results revealed that using steel wool reduces the PV temperature by 9.9 oC and increases the outlet temperature by 4.41 oC at the air flow rate of 0.17 kg/s. …”
Get full text

Behavior of Hollow Thin Welded Tubes Filled with Sand Slag Concrete by Noureddine Ferhoune, Meriem Senani, Abdelhamid Guettala

“…This paper presents the axial bearing capacity of thin welded rectangular steel stubs filled with concrete sand. A series of tests was conducted to study the behavior of short composite columns under axial compressive load; the cross section dimensions were 100 × 70 × 2 mm. …”
Get full text

Research on Pure Modes I and II and Mixed-Mode (I/II) Fracture Toughness of Geopolymer Fiber-Reinforced Concrete by Sundaravadivelu Karthik, Kaliyaperumal Saravana Raja Mohan, Gunasekaran Murali, Gobinath Ravindran

“…Four different fibers were used, such as polypropylene and steel fiber (short and long), at a dosage of 1.5% by volume. …”
Get full text

Effect of Internal Curing with Superabsorbent Polymers on Bond Behavior of High-Strength Concrete by Xiao Lei, Rui Wang, Hanwan Jiang, Faxiang Xie, Yanni Bao

“…Meanwhile, the bond performance between reinforcing steel and SAP HSC concrete remains unknown. In this paper, the bond performance of HSC mixed with SAP is studied by pull-out tests, and the results were obtained as follows: (1) the bond strength of HSC mixed with SAP increased first and then decreased with the increase of SAP content; (2) the slip at ultimate bond strength of HSC with SAP decreased with the increase of compressive strength; (3) a prediction model of the stress-slip relationship between steel rebars and HSC was established.…”
Get full text

Design and Analysis of thermosyphon Solar Water Heating System. by Kakuru, Stephen

“…The system is made of a 4m2 flat plate collector to convert solar energy into thermal energy, an insulated stainless steel storage tank of 240 liters capacity for storing hot water, a pipe system for transporting water, and a painted mild steel frame for supporting the system. …”
Get full text

CREATION OF HIGH TECHNOLOGICAL PROCESSES AND AGGREGATES AT THE BELORUSSIAN METALLURGICAL WORKS. INNOVATION ACTIVITY by M. V. Miasnikovich, V. I. Timoshpolskij, N. V. Andrianov

Get full text

INTEGRATION OF COMPUTER TECHNOLOGIES SMK: AUTOMATION OF THE PRODUCTION CERTIFICA-TION PROCEDURE AND FORMING OF SHIPPING DOCUMENTS by S. A. Pavlenko

Get full text

TECHNICAL DIAGNOSTIC OF EQUIPMENT OF METALLURGICAL SHOPS, PERSPECTIVES OF DEVELOP-MENT by A. N. Kattsyn

Get full text

COMPETITIVENESS OF METAL PRODUCTION OF RUP ‘BMZ» ON THE INTERNATIONAL COMMODITY MARKETS by M. V. Kuzmich

Get full text

PROVIDING OF ACCURACYOF THE DEFORMATION CHARACTERISTICS MEASUREMENT by A. S. Romankov

Get full text

MODEM AUTOMATION OF ACCOUNTING AT RUP «BMZ» WITH APPLICATION OF 2D-SCAIMERS by A. U. Gapanuk

Get full text

REDUCTION OF THE PRODUCTION COST. EXPERIENCE OF THE COSTS REDUCTION AT RUP “BMZ” by S. S. Sereda

Get full text

MATERIALS FOR PRODUCTION OF METAL MOLDS by A. Ju. Jakovlev, I. P. Volchek

“…The influence of alloying with manganese, chromium, nickel, copper and molybdenum on mechanical characteristics and thermocyclic endurance of grayed steel and possibility of its application for metal casting molds is investigated.…”
Get full text