Real-Time Monitoring and Early Warning Method Utilizing FBG Sensors in the Retrofitting Process of Structures by Shuli Fan, Liang Ren, Hongnan Li, Biao Song

“…Eight FBG sensor clusters consisting of a strain sensor and a temperature sensor were welded on the steel beam surface. Using these FBG sensors, the real-time strains in key positions during the cutting process of steel beam were measured. …”
Get full text

Performance of Cracked Ultra-High-Performance Fiber-Reinforced Concrete Exposed to Dry-Wet Cycles of Chlorides by Longlong Niu, Shiping Zhang

“…Although self-healing is hard to cease the corrosion of steel fibers, it can relieve the corrosion of steel fibers and improve the flexural strength exposed to 100 dry-wet cycles.…”
Get full text

Mathematical Modeling of Turbulent Gas Flames and Assessment of Environmental Indicators of Modern Gas Burning Devices by K. V. Dobrego, S. A. Zhdanok, V. I. Timoshpolsky, I. M. Kozlov, V. A. Tishchenko, I. V. Kotov

“…This method is used to justify the selection of burners for state-of-the-art furnaces of the Republican Unitary Enterprise (RUE) «Byelorussian Steel Mills».…”
Get full text

NUMERICAL MODELING OF STRESSES NEAR THE SURFACE IN THE INGOT OF CIRCULAR SECTION, CRYSTALLIZABLE AT CIRCULAR TORCH SECONDARY COOLING by A. N. Chichko, N. V. Andrianov, A. V. Demin, D. M. Kukuj, V. F. Sobolev, Ju. V. Jatskevich, O. I. Chichko

“…The results of computer calculations of the stresses, generated in outside layer of ingot of steel 20 of circular section with diameter 300 mm, in application to one of the industrial technological schemas of RUP “BMZ”, are presented. …”
Get full text

Life Cycle Assessment of Environmental Impact of Steelmaking Process by Huimin Liu, Qiqiang Li, Guanguan Li, Ran Ding

“…The steel industry is facing problems such as serious environmental pollution and high resource consumption. …”
Get full text

Pemodelan 3D Jembatan Lengkung, Studi Kasus Jembatan Bukit Sulap, Menggunakan Software Autodesk Revit by Muhammad Ihsanul Kharimah, Benny Hidayat

“…In this research, modelling of a steel truss bridge with an arch type was carried out using Autodesk Revit software. …”
Get full text

An investigation of cracks caused by concrete shrinkage and temperature differences in common reinforced concrete bridge structures by Van-Hau Nguyen

“…The use of smaller diameter reinforcement can significantly reduce crack width compared to larger ones, given the same steel ratio. However, a high steel ratio, while reducing crack width, increases susceptibility to cracking. …”
Get full text

Investigation of Bending, Sound Absorption, and Damping Properties of AZ91D-Swivel Plate by Saravanan Annamalai, Suresh Periyakgoundar, Kumaravel Paramasivam, Aravindha Balaji Selvaraj

“…A comparison was made between Mg alloy and A3 steel on weight, bending, sound absorption, and vibration conditions. …”
Get full text

Empirical model for estimating the surface roughness of machined components under various cutting speed by JO Osarenmwinda

“…The Mean Absolute Percent Deviation (MAPD) which measures absolute error as a percentage was found to be 1.46% (stainless steel), 4.55 %( mild steel) and 4.76% (aluminum cast) respectively. …”
Get full text

Empirical model for estimating the surface roughness of machined components under various cutting speed by JO Osarenmwinda

“…The Mean Absolute Percent Deviation (MAPD) which measures absolute error as a percentage was found to be 1.46% (stainless steel), 4.55 %( mild steel) and 4.76% (aluminum cast) respectively. …”
Get full text

Development and characteristic of SFRCR-ECC as a novel multifunctional version of fire-resistive and corrosion-resistive coating by Junyu Yang, Liang Li, Jutao Chen, Yan Xiong, Kairen Lin, Solomon Tesfamariam

“…At the same time, twice coating of anticorrosive primer and fireproofing on steel substrate reduces both cohesive properties of the steel substrate. …”
Get full text

SYSTEM OF PERSONNEL MANAGEMENT: WHEN HONOR IS MORE EXPENSIVE THAN MONEY by S. G. Kornienkov, D. V. Gritsaenko

Get full text

TO THE ISSUE OF DETERMINATION OF THE INSURABLE RESERVE VOLUME by N. V. Andrianov, O. V. Shchukina

Get full text

DEVELOPMENT OF THE METHODS OF CARRYING OUT OF INTERLABORATORY COMPARING TESTS by T. I. Akatejva, T. P. Kurenkova

Get full text

Carbon rod production technology by V. V. Filippov, A. V. Steblov, S. A. Isakov

Get full text

RESEARCH ON DYNAMIC PROPERTY FOR CASTING CRANE IN THE LOAD-LIFTING PROCESS BASE ON THERMO-ELASTIC COUPLING by HUANG Bin, FENG LiXia, XIANG ZaiYu

“…As the rapid development of steel smelting industry,the casting cranes are developed tend to high speed and large-scale. …”
Get full text

Investigation of Rock Failure Pattern in Creep by Digital Speckle Correlation Method by Yunliang Tan, Yanchun Yin, Tongbin Zhao

“…In order to study the mechanical characteristics from creep deformation to failure of rock, the tests of uniaxial compression and pushing steel-plate anchored in rock were performed, by using RLJW-2000 servo test synchronizing with Digital Speckle Correlation Method (DSCM). …”
Get full text

Comparative Analysis of Optical Signals Emitted by Corona on a Laboratory Model of Transmission Lines Made of Various Materials by Sławomir Krzewiński, Paweł Frącz, Ireneusz Urbaniec, Tomasz Turba

“…Three aluminium-based materials were chosen: pure aluminium, aluminium with added magnesium, and aluminium with added silicon, and for comparison purposes also, steel-based lines were considered: copper-coated steel and steel with added chromium and nickel. …”
Get full text

Computational Fluid Dynamics Analysis of Temperature Distribution in Solar Distillation Panel with Various Flat Plate Materials by Trismawati Trismawati, Hendry Y. Nanlohy, Helen Riupassa, Susi Marianingsih

“…Additionally, observations indicated that the amount of convection occurring in copper flat plates was 121.108 Watts; in aluminum, it was 118.517 Watts; and in stainless steel, it was 105.05 Watts. The radiation energy for stainless steel flat plates was 29.93 W; for copper, 16.14 W; and for aluminum, 13.49 W.…”
Get full text

Static Mechanical Properties and Microscopic Analysis of Hybrid Fiber Reinforced Ultra-High Performance Concrete with Coarse Aggregate by Shengbing Liu, Yonglei Zhang

“…Considering the mass replacement rate of coarse aggregate (10%, 15%, 20%, and 30%), the steel fiber volume rate (0%, 0.5%, 1.0%, and 1.5%), and the polypropylene fiber volume rate (0%, 0.05%, 0.10%, and 0.15%). …”
Get full text