-
1881
The Influence of Neck Muscle Activation on Head and Neck Injuries of Occupants in Frontal Impacts
Published 2018-01-01“…A mixed dummy-human finite element model was developed to simulate a frontal impact. …”
Get full text
Article -
1882
Microstructural analysis and mechanical properties of Ni35Co25.5Al16Fe15.5Cr8 high-entropy alloy in the as-cast and homogenized conditions
Published 2025-01-01“…The estimated ultimate strength obtained using the SP method is approximately 840 MPa for the homogenized sample, compared to 644 MPa for the as-cast sample. Finite element simulations of the small punch test were conducted to validate the experimental results. …”
Get full text
Article -
1883
Study on the Dynamic Problems of Double-Disk Rotor System Supported by Deep Groove Ball Bearing
Published 2019-01-01“…In this paper, the nonlinear finite element method is used combined with the structural characteristics of deep groove ball bearings. …”
Get full text
Article -
1884
Experimental Study on Influence of Microexpansive Concrete Self-Stress on Performance of Steel Pipe Concrete
Published 2021-01-01“…The yield and ultimate strength of the HSTCMC short columns can be enhanced to 8.9% and 14.6%, and with the content of expansive agent that increased from 8% to 12%. The finite element analysis results highlighted that the end constraint at the two ends has the biggest influence on the mechanical performance of the HSTCMC short columns, followed by the thickness of the steel tube and the content of the expansive agent. …”
Get full text
Article -
1885
Comparisons between Asphalt Pavement Responses under Vehicular Loading and FWD Loading
Published 2020-01-01“…Except for field measurements, the finite element (FE) models of the experimental pavements were established to simulate the pavement responses under a wide range of loading conditions. …”
Get full text
Article -
1886
Study on Wind Resistance Performance of Transmission Tower Using Fixture-Type Reinforcement Device
Published 2025-01-01“…This paper uses the finite element method to investigate the influence of a fixture-type reinforcement device (FRD) on the load-bearing performance of the transmission tower structure and explores the effects of different numbers of fixture pairs on the reinforcement. …”
Get full text
Article -
1887
Influence of drilling incidence angle on the drilling force distribution of pneumatic impactor
Published 2025-01-01“…Based on the dynamic theory of impact drilling and finite element method (FEM), the constitutive model of HJC criterion and INVENTOR 3D mechanical structure design software, a 3D numerical analysis system of piston-bit head-rock during pneumatic impactor drilling is established by ANSYS LS-DYNA, a nonlinear dynamic analysis software. …”
Get full text
Article -
1888
Performance analysis of dual stator six‐phase embedded‐pole permanent magnet synchronous motor for electric vehicle application
Published 2023-03-01“…For performance evaluation, the Finite Element Method analysis is chosen, as it gives appropriate and precise results. …”
Get full text
Article -
1889
Microarchitecture Parameters Describe Bone Structure and Its Strength Better Than BMD
Published 2012-01-01“…The geometrical mesh of layers of bone mass obtained from microCT investigation and the volumes of each layer and fractal dimension were calculated. The finite element method was applied to calculate the compression force F causing ε=0.8% strain. …”
Get full text
Article -
1890
Thermal analysis of transient MHD ferrofluid flow and natural convection in a Porous cavity with a cylindrical barrier
Published 2025-02-01“…The governing equations for the ferrofluid flow have been solved using Galerkin's finite element method. The boundary conditions are the cylindrical barrier, a part of the lower face of the cavity having a high temperature, the side faces of the cavity having a low temperature, and the remaining parts adiabatic. …”
Get full text
Article -
1891
Numerical simulation study on coal seam response characteristics of shallow three-electrode laterolog
Published 2025-02-01“…In this paper, through the finite element simulation software COMSOL Multiphysics, 2D and 3D models are constructed based on shallow three-electrode laterolog, and the characteristics of using shallow three-electrode laterolog in coal field logging are studied. …”
Get full text
Article -
1892
Simulation Study on the Impact Response of Barrels with Different Rifling Profiles during Bullet Engraving
Published 2022-01-01“…/Explicit software was used to build a finite element model of the barrel dynamic stress under heat-force-friction coupling during bullet engraving. …”
Get full text
Article -
1893
Numerical Analysis of Two I-shaped GFRP Composite Bridge with Corrugated Webs
Published 2021-01-01“…Three-dimensional finite element (FEA) models are created to simulate the flexural behavior of two-I-shaped-girder composite bridge with straight webs, and the model result is validated with experimental data. …”
Get full text
Article -
1894
Numerical Investigation of Pinned Fuse with Simple Replacing in Steel Eccentrically Braced Frames and Design Parameters Determination
Published 2024-05-01“…The results of the numerical studies conducted on the integrated three-dimensional finite element model of the eccentric frame equipped with a fuse show that the damage was limited to the fuse section, and no other structural components were damaged. …”
Get full text
Article -
1895
Three-Dimensional Wave-Field Characteristics of Earth-Rock Dams with Different Hidden Hazards
Published 2018-01-01“…Based on the equivalent elastic wave theory in isotropic mediums, the three-dimensional wave field of earth-rock dams with different defects was calculated using the finite element numerical simulation method. The characteristic and regularity of the three-dimensional wave field was explored. …”
Get full text
Article -
1896
Analisis tegangan pada struktur mesin pencacah plastik menggunakan metode elemen hingga (MEH) dan uji kerja mesin pencacah plastik
Published 2021-04-01“…The strength of plastic shredding and injection machines can be calculated by means of simulation using the finite element method (FEM). This method will save costs, selection of materials and cutting edge shapes quickly and easily and soon. …”
Get full text
Article -
1897
Quality optimization of liquid silicon lenses based on sequential approximation optimization and radial basis function networks
Published 2025-02-01“…The method successfully minimizes residual stress and volume shrinkage, thereby improving product quality and manufacturing efficiency. By replacing finite element reanalysis with the RBF network, it constructs an approximate functional relationship between process conditions and quality. …”
Get full text
Article -
1898
Behavior of an Innovative Square Composite Column Made of Four Steel Tubes at the Corners and Corrugated Steel Batten Plates on all Sides
Published 2019-01-01“…Through the experimental and finite element (FE) numerical simulation calculations, the axial compression performance and seismic performance of the ISSCC column were discussed, and the FE model was verified through experimental results. …”
Get full text
Article -
1899
Development of Vacuum Vessel Design and Analysis Module for CFETR Integration Design Platform
Published 2016-01-01“…This design/analysis workflow could automate the process of modeling and finite element (FE) analysis for vacuum vessel. Functions such as sensitivity analysis and optimization of geometric parameters have been provided based on the design/analysis workflow. …”
Get full text
Article -
1900
Dynamic Characteristics and Seismic Response of Multi-Story Wooden Tower Considering the Influence of a High Stylobate
Published 2025-01-01“…In situ dynamic tests were conducted on Caiyunjian Tower to investigate the influence of a high stylobate on its dynamic characteristics and seismic response through time–domain and frequency–domain methods. Finite element models were developed for Caiyunjian Tower (wooden structure and platform) and the overall structure including the high stylobate. …”
Get full text
Article