-
1001
Dynamic structural characteristics and vibration susceptibility of Tongren loess under the influence of water content and confining pressure
Published 2025-01-01“…However, the dynamic friction angle is less affected by water content changes, decreasing by 18% ~ 25% when saturated. …”
Get full text
Article -
1002
Numerical Simulation of the Influence of Natural Fractures on Hydraulic Fracture Propagation
Published 2020-01-01“…Furthermore, the effects of the approach angle, principal stress difference, tensile strength and length of the natural fracture, and elastic modulus and Poisson’s ratio of the reservoir on the propagation law of a hydraulic fracture are investigated. …”
Get full text
Article -
1003
Stability analysis of three-dimensional slope reinforced by natural fiber include wheat straw and bamboo
Published 2025-02-01“…Both safety and economy of reinforced slope are considered, the reasonable design slope angle of reinforced slope is 30° to 60°, where β = 30° is the ideal design slope angle. …”
Get full text
Article -
1004
Investigation of the Atomic Structure of Ge-Sb-Se Chalcogenide Glasses
Published 2018-01-01“…By increasing the Sb content, both the Se-Ge-Se bonds angle of 107±3° and Se-Sb-Se bonds angle of 118±3° decrease, respectively, indicating distortion of the structural units. …”
Get full text
Article -
1005
Analysis of Indicators for Assessing the Risk of Progression from PACS to APAC and the Degree of Intraocular Pressure Elevation in APAC Using AS-OCT
Published 2024-01-01“…The aim of this study is to quantify anterior chamber parameters to provide potential risk indicators for evaluating the progression of primary angle-closure suspect (PACS) eyes to acute primary angle closure (APAC) and the degree of intraocular pressure elevation in patients with APAC utilizing anterior segment optical coherence tomography (AS-OCT). …”
Get full text
Article -
1006
Effect of bar jump height on kinetics and kinematics of take-off in agility dogs.
Published 2025-01-01“…With increasing bar height, the horizontal velocity of trunk decreased (p<0.001), and take-off angle became steeper (p<0.001), with all bar heights differing from each other (p<0.01). …”
Get full text
Article -
1007
A Method to Evaluate Orientation-Dependent Errors in the Center of Contrast Targets Used with Terrestrial Laser Scanners
Published 2025-01-01“…Errors of under 0.3 mm were observed in the target center as a function of the angle for the two distances at high resolution (109 ppd).…”
Get full text
Article -
1008
The Mechanism of Rock Mass Crack Propagation of Principal Stress Rotation in the Process of Tunnel Excavation
Published 2021-01-01“…The results show that the “relative initial angle” of crack angle is being updated in time during the principal stress rotation process; once the stress is rotated, it will become the next initial crack angle; the crack propagation direction is deviated under the applied shear load, and it is always in the direction of minimum shear load, leading to a certain degree of inhibition of crack propagation depth in the initial direction. …”
Get full text
Article -
1009
Reinforcement Effect of Inclined Prestressed Concrete Pipe Piles on an Inclined Soft Foundation
Published 2020-01-01“…Moreover, as the inclination angle of PCP piles increases, the maximum displacement decreases rapidly, associated with greatly enhanced lateral stability.…”
Get full text
Article -
1010
Fluctuations Driven by Multicomponent Pickup Ion Distributions in the Outer Heliosheath
Published 2025-01-01“…The AC waves quickly scatter the PUIs with pitch angles away from 90 ^∘ toward isotropy, while the PUIs near 90 ^∘ pitch angle maintain a degree of anisotropy within our simulation timeframe. …”
Get full text
Article -
1011
Optimizing heat transfer in a finned rectangular latent heat storage system using response surface methodology
Published 2025-02-01“…Several fin designs, angles, and arrangements are examined using the Response Surface Methodology (RSM) and the Taguchi technique to optimize energy storage performance. …”
Get full text
Article -
1012
Experimental Study on the Shear Behavior of Bolted Concrete Blocks with Oblique Shear Test
Published 2018-01-01“…An oblique shear apparatus, which could simultaneously apply shear and normal force on tested samples at three slope angles (53°, 58°, and 63°) of a predetermined shear plane, was employed. …”
Get full text
Article -
1013
The Interaction Force between Scheelite and Scheelite/Fluorite/Calcite Measured Using Atomic Force Microscopy
Published 2020-01-01“…The mechanism of the formation of the hydrophobic agglomerate in fine scheelite flotation was studied using zeta potential measurement, contact angle measurement, optical microscope measurement, and atomic force microscopy (AFM) colloid probe technology. …”
Get full text
Article -
1014
Analysis of the Outer Contour Characteristics of Roadway Forming under the Influence of Cutting Head Vibration
Published 2021-01-01“…With the increase of the cutting lifting angle, the maximum and average value of the difference between the “pit” and the uplift “peak ridge” on the coal and rock shows an increasing trend, and with the increase of the cylinder pressure, the maximum values of the horizontal swing angle “pit” and the uplift “peak ridge” gradually increase. …”
Get full text
Article -
1015
Experimental dataset of a model-scale ship in calm water and wavesUniversity of Southampton Institutional Repository
Published 2025-02-01“…Various test configurations are explored, encompassing four rudder angles, five leeway angles, two wave conditions, and two propeller speeds. …”
Get full text
Article -
1016
Multislice B1 Mapping Method Using Magnetic Resonance Composite Spin Echo Sequences and Simultaneous Echo Refocusing
Published 2023-01-01“…To evaluate the performance of the proposed B1 mapping method, computational simulations were performed and compared with Morrell’s method, double angle method, and Yarnykh’s method. These results showed that the angle-to-noise ratio of the proposed B1 mapping method has wider B1 range compared to that of other B1 mapping methods. …”
Get full text
Article -
1017
Optimization of Shear-Thickening Polishing Parameters for Optical Glass Based on Grey Relational Analysis
Published 2025-01-01“…The results indicate that slurry concentration has the most significant impact on the optimization objective, followed by polishing angle, whereas polishing speed has the least effect. …”
Get full text
Article -
1018
Effect of the Preexisting Fissure with Different Fillings in PMMA on Blast-Induced Crack Propagation
Published 2018-01-01“…The preexisting fissure with different angles (θ = 0°, 45°, and 90°) and different distances (L = 20, 30, 40, 50, and 60 mm) was prefabricated around the borehole. …”
Get full text
Article -
1019
A harmonic model validation methodology for power generation units based on voltage-current phasor characteristic
Published 2025-04-01“…The proposed methodology considers both the phase angle and magnitude of harmonic quantities and also their correlation. …”
Get full text
Article -
1020
The Mechanisms of Medial Pedicle Wall Violation: Insertion Method Is as Important as Correct Cannulation of the Pedicle
Published 2014-01-01“…The study presents finding out the effect of insertion angle and insertion force on medial wall violation. …”
Get full text
Article