Investigation on Microstructure and Tensile Fractography of RE Oxides (CeO2/Y2O3) Reinforced AZ91D Magnesium Matrix Composites by Santhosh Gotagunaki, Vardhaman S. Mudakappanavar, R. Suresh

“… The current work aims to investigate the mechanical properties of rare oxide reinforced Mg alloy based MMCs. Magnesium matrix considered in the study is AZ91D alloy, whereas rare earth oxides reinforced were CeO2 and Y2O3. …”
Get full text

Atomic mobility in Titanium grade 5 (Ti6Al4V) by Gierlotka W., Lothongkum G., Lohwongwatana B., Puncreoburt C.

“…It is obvious, that heat treatment of the alloy will change a ratio between BCC_A2 and HCP_A3 and, as a consequence, properties of a material. …”
Get full text

Effect of carbon and manganese content on the microstructure and mechanical properties of high manganese austenitic steel by Gürol U., Can Kurnaz S.

“…The solution annealing fully dissolved the carbides in the alloys with lower carbon content (1wt%) and resulted in a homogeneous austenitic microstructure. …”
Get full text

Electrochemical Tests to Evaluate the Stability of the Anodic Films on Dental Implants by C. E. B. Marino, L. H. Mascaro

“…The stability of anodic films potentiodynamically grown on titanium, titanium-grade 2, and Ti6Al4V alloy was studied in a simulated physiological electrolyte, up to 8.0 V, and at room temperature to determine the corrosion resistance levels of dental implants. …”
Get full text

GROWTH OF CRYSTALS OF PRIMARY ALUMINIUM WITH ROSETTE MORPHOLOGY AT CASTING OF SILUMINS by E. I. Marukovich, A. G. Borisov, Ju. A. Lebedinskij, A. M. Branovitskij

“…The work is devoted to actual theme of alloy solidifi – investigation of infl of overlapping of thermal and concentration fi of neighboring crystals to forming of non- dendrite structures. …”
Get full text

ENVIRONMENTALLY SAFE CONTINUOUS CASTING OF HYPEREUTECTIC FINE-CRYSTALLINE SILUMIN INGOTS by V. Ju. Stetsenko, A. M. Pevnev, Suk-Bong Kang

“…It is shown that continuous horizontal casting of alloy AK18 into jet crystallizer with application of flooded – jet systems of ingot cooling and hereditary modifying enables to create ecologically safe technological process of production of alloy AK18 ingots in diameter of 40 mm with dispersion of eutectic silicon crystals less than 20 mm.…”
Get full text

Fatigue fracture mechanism of Ni-base superalloy GH4065A at elevated temperatures by LI Linhan, ZHANG Ji, ZHANG Wenyun, TIAN Qiang, QIN Heyong, ZHANG Beijiang

“…GH4065A is a newly developed high-performance cast-wrought Ni-base superalloy with ultra-low C and N content used for advanced turbine engine disc. In this study， the alloy’s inclusions of the alloy are characterized and statistically analyzed. …”
Get full text

Thermodynamic calculation of phase equilibria in stainless steels by Klančnik G., Petrovič Steiner D., Medved J.

“…The complex melting behavior was evident for both alloy systems. Experimentally obtained data were compared with the results of the thermodynamic calculations using the CALPHAD method. …”
Get full text

PENGARUH MATERIAL TERHADAP DEFORMASI, STRAIN, DAN SAFETY FACTOR PADA BRACKET CALIPER MENGGUNAKAN METODE ELEMEN HINGGA by Andi Abdullah Ghyferi, Aldias Bahatmaka, Muhammad Yusuf Wibowo, Ahmad Anwar, Ayyub Ridananda, Anggi Vandika

“…The purpose of this study is to analyze the deformation, equivalent elastic strain, and safety factor of a bracket bracket made from two different materials by using the Finite Element Method, specifically aluminum alloy 6061 T6 and cast iron EN GJL 100. The result of this study is that the Aluminum Alloy 6061T6 material has a deformation of 3.57E-04 whereas the Cast iron EN GJL 100 material is 2.75E-04. …”
Get full text

Developing an Empirical Relationship to Predict the Wear Characteristics of Ni-Based Hardfaced Deposits on Nuclear Grade 316LN Austenitic Stainless Steel by S. Gnanasekaran, Samson Jerold Samuel Chelladurai, G. Padmanaban, Ramesh Arthanari, V. Balasubramanian

“…Using the nickel-based Colmonoy 5 hardfacing alloy, components made of austenitic stainless steel (ASS) used in nuclear power plants can be hardfaced. …”
Get full text

Investigations on microstructure and mechanical properties of Mg-5wt.% Cu-TiB2 composites produced via powder metallurgy route by Stalin B., Ravichandran M., Mohanavel V., Raj L.P.

“…Magnesium alloy matrix composite reinforced with constant weight fraction of 5% Cu and various weight fractions of (0%, 5%, 10%, 15%) titanium diboride (TiB2) fabricated by Powder Metallurgy route. …”
Get full text

Improving the Corrosion Resistance of NiNb-Based Bulk Metallic Glass through the Hot Compression by Abeer Abdullah Al Anazi, Andrés Alexis Ramírez-Coronel, Rasha Fadhel Obaid, Abdullah Albaker, M. Abdulfadhil Gatea, Seyed Mojtaba Mostafavi

“…The polarization test unveiled that the hot compression deteriorated the corrosion resistance of the Ni55Nb45 alloy through the introduction of anomalous chemical interfaces. …”
Get full text

Mechanical, wear, and fracture behavior of Titanium Diboride (TiB2) - Cerium Oxide (CeO2) reinforced Al-6061 hot-rolled hybrid composites by S. R. Sreenivasa Iyengar, D. Sethuramu, M. Ravikumar

“…. % of TiB2 (2.5%, 5%, 7.5% and 10%) particulates and constant 5% of CeO2 particulates. The monolithic alloy and hybrid composite were hot-rolled at a temperature of 515�C. …”
Get full text

Microstructure evolution and recrystallization behavior of two nickel-based single crystal superalloys by XU Fuze, LIN Yongcheng, MA Dexin, HE Daoguang, ZHAO Yunxing, LI Lyu, CHENG Bowen, DENG Yangpi

“…The micro-shrinkage porosity and eutectic content of the as-cast and solution heat treated CMSX-4 alloy are both higher than those of the DD5 alloy. …”
Get full text

Biosafety and efficacy evaluation of a biodegradable Zn-Cu-Mn stent: A long-term study in porcine coronary artery by Yi Qian, Yan Chen, Jimiao Jiang, Jia Pei, Junfei Li, Jialin Niu, Jinzhou Zhu, Guangyin Yuan

“…In this study, biodegradable Zn-Cu-Mn alloy stents were implanted into porcine coronary artery for 18 months, and the in vivo biosafety and efficacy as well as the degradation behavior were systematically studied. …”
Get full text

Microstructural Changes and Mechanical Response of Aluminum-Based Composites Prepared with Dispersed CeO2 Nanoparticles by Francisco J. Baldenebro-López, Raúl Peréz-Bustamante, Ivanovich Estrada-Guel, Roberto Martínez-Sánchez, Alberto Duarte-Moller, Cynthia D. Gómez-Esparza

“…The effect of CeO2 nanoparticles on the microstructure of two different metal matrixes, AA2024 aluminum alloy and pure aluminum, were studied. The aluminum-based composites were synthesized by mechanical milling and subsequently sintering at 550°C under an argon atmosphere. …”
Get full text

Performance Analysis and Optimisation During Machining of Al-ZrB2 Reinforcement-Based Metal Matrix Nanocomposites Using Coated and Uncoated Insert by Seema V. Yerigeri, Vaijanath V. Yerigeri

“…Al 7075, Al6082 and Al 6063 are selected alloy levels, while zirconium diboride (ZrB2) reinforcement levels are set at 6, 9 and 12 wt.%. …”
Get full text

Effect of aluminizing coating on fatigue properties of DD6 single crystal superalloy by DONG Jianmin, LI Jiarong, ZHEN Zhen, XU Zhenhua

“…To investigate the effects of aluminizing coating on the surface integrity and rotational bending high cycle fatigue performance of DD6 alloy， the chemical vapor deposition method is used to aluminize DD6 fatigue samples after standard heat treatment. …”
Get full text

Investigation on Inorganic Salts K2TiF6 and KBF4 to Develop Nanoparticles Based TiB2 Reinforcement Aluminium Composites by Vinayagam Mohanavel, K. Ravi Kumar, T. Sathish, Palanivel Velmurugan, Alagar Karthick, M. Ravichandran, Saleh Alfarraj, Hesham S. Almoallim, Shanmugam Sureshkumar, J. Isaac JoshuaRamesh Lalvani

“…In the current research, AA6082 aluminium alloy matrix composites (AAMCs) incorporated with various weight fractions of titanium diboride (0, 3, 6, and 9 wt%) were prepared via an in situ casting technique. …”
Get full text

Kinetics, thermodynamics, and catalysis of the cation incorporation into GeO2, SnO2, and (SnxGe1−x)O2 during suboxide molecular beam epitaxy by Wenshan Chen, Kingsley Egbo, Joe Kler, Andreas Falkenstein, Jonas Lähnemann, Oliver Bierwagen

“…The (SnxGe1−x)O2 alloy system is in its infancy, and molecular beam epitaxy (MBE) is a well-suited technique for its thin-film growth, yet it presents challenges in controlling the alloy composition and growth rate. …”
Get full text