Design and Numerical Investigation on Octagonal Barge-Type FOWT with Counterweight Suspension System by Yung-Chun Sun, Ray-Yeng Yang

“…It uses SolidWorks for modeling, Ansys AQWA for hydrodynamic calculations, and Orcina OrcaFlex for wind/wave/current coupling dynamic analysis. …”
Get full text

Design and Optimization of a Triangular Shear Piezoelectric Acceleration Sensor for Microseismic Monitoring by Yannan Shi, Shuaishuai Jiang, Yang Liu, Yiying Wang, Penglei Qi

“…The parametric design of the designed sensor is carried out, and its finite element structural model is built by ANSYS. The modal analysis, resonance response analysis, and piezoelectric analysis of the designed sensor are carried out. …”
Get full text

Design of modernized test bench for analysis of cooling systems with intensification under inertial forces field by V. V. Shalay, K. V. Shcherban

“…This bench will allow investigation the efficiency of heating the hydrocarbon coolant in the field of inertial forces and verification of the calculation results obtained in ANSYS environment…”
Get full text

Modal Analysis of 27 mm Piezo Electric Plate for Small-Scale Underwater Sonar-Based Navigation by M. O. Afolayan, D. S. Yawas, C. O. Folayan, S. Y. Aku

“…A test on a 27 mm diameter buzzer piezo plate shows promising performance under water at frequencies from 4.5 kHz to 80 kHz. ANSYS-based simulation was therefore used to find modal frequencies at higher frequencies so as to optimize this encouraging result. …”
Get full text

Cyclic Behavior and Modeling of Bolted Glulam Joint with Cracks Loaded Parallel to Grain by Jing Zhang, Zhi-Fang Liu, Yong Xu, Mai-Li Zhang, Liu-Cheng Mo

“…A three-dimensional (3D) numerical model was established in software package ANSYS to investigate the cyclic behavior of bolted glulam joints with local cracks. …”
Get full text

Aerodynamic Optimization of a UAV Wing subject to Weight, Geometric, Root Bending Moment, and Performance Constraints by Durmuş Sinan Körpe, Öztürk Özdemir Kanat

“…The outcomes are compared with the results of the solver based on the nonlinear lifting-line theory implemented into XLFR5 and the transition shear stress transport model implemented into ANSYS-Fluent. The agreement between the results at the low and moderate angle of attack values is observed. …”
Get full text

Buckling Analysis of Sandwich Plate Systems with Stiffening Ribs: Theoretical, Numerical, and Experimental Approaches by Guangping Zou, Yuyang Wang, Qichao Xue, Chunwei Zhang

“…An FEM study on elastic buckling was then conducted via ANSYS software. The advantages of the SPS were highlighted via its elastic eigenvalue buckling numerical analysis with multiple stiffeners. …”
Get full text

Research on End-Effector Position Error Compensation of Industrial Robotic Arm Based on ECOA-BP by Wenping Xiang, Junhua Chen, Hao Li, Zhiyuan Chai, Yinghou Lou

“…The kinematic model of the robotic arm was established using the Denavit–Hartenberg (DH) parameter method, and a rigid–flexible coupled virtual prototype model was developed using ANSYS and ADAMS. Kinematic simulations were performed on the virtual prototype to analyze the variation in end-effector position errors under rigid–flexible coupling conditions. …”
Get full text

Waveform Characteristics of Tunnel Blast Waves and a Wave-Blocking Method by Xianshun Zhou, Xuemin Zhang, Tianhe Ren, Xuefeng Ou, Wenchao Xiong, Liming Zhang, Lei Zhang

“…Furthermore, a numerical simulation for the impact process of the NWBT was established using the ANSYS/LS-DYNA software. Finally, it was found that a shorter distance from the NWBT to the source of the blast makes a better contribution to its wave-blocking effect. …”
Get full text

Analysis of Nonlinear Vibration of Hard Coating Thin Plate by Finite Element Iteration Method by Hui Li, Liu Ying, Wei Sun

“…And consequently specific analysis procedure is proposed by combining ANSYS APDL and self-designed MATLAB program. Finally, a composite plate coated with MgO + Al2O3 is taken as a study object and both nonlinear vibration test and analysis are conducted on the plate specimen with considering strain dependent mechanical parameters of hard coating. …”
Get full text

Mechanical Behavior of Q460 High-Strength Steel under Low-Cycle Fatigue Loading by Xue Han, Min Chang, Haifeng Li, Hualin Cao, Baoan Cao

“…In addition, a finite element model of the specimen under cyclic load was established with ANSYS and the numerical results were compared with those of the experimental tests. …”
Get full text

Strengthening of Steel Columns under Load: Torsional-Flexural Buckling by Martin Vild, Miroslav Bajer

“…The study includes results gained from finite element models of the problem created in ANSYS software. The results obtained from the experiments and numerical simulations were compared.…”
Get full text

Acoustic calculation of process pipelines of a compressor station for assessing low-frequency pressure pulsations in dead-end branches by Alexander S. Schreder, Oleg A. Kurasov, Petr V. Burkov, Alexey N. Gavrilin

“…The paper introduces the results of the acoustic calculation carried out in the ANSYS Workbench software. According to these results the authors determined the pulsation amplifications in the dead-end branches, which are relatively large and can be the cause of high low-frequency vibrations.   …”
Get full text

The effect of chimney entrance slope and constricted section on the performance of solar chimney power plants: A CFD approach by Kaplan Mahmut

“…A computational fluid dynamics model (CFD) is constructed based on Manzanares plant with a chimney height (H) of 194.6 m via ANSYS FLUENT. The novel configurations are generated by changing the chimney inlet slope, θ (45°-85°) and radius of the constricted section with a fixed height (H/28). …”
Get full text

Study on Optimization of Delay Method of Wedge Cut Blasting in Tunnel by Wenle Gao, Zhicheng Liu, Yanping Wang, Zhenwei Yan, Zehua Zhang

“…Relying on the entrance section of a high-speed railway tunnel blasting project, the fluid-solid coupling algorithm based on ANSYS/LS-DYNA was used to optimize the parameters of wedge cut blasting, and the vibration could be reduced on the basis of ensuring the blasting effect. …”
Get full text

Structural behavior of Lightweight and High strength Layered Hollow Core Slabs by Asmaa Ghamry, Ahmed Esia, Louay Aboul-Nour

“…Using shear dowels ensures an efficient bond between the two layers of the tested slabs. ANSYS program used for modelling the slab. The numerical study accepted the experimental data with a variation of less than 10% for all slabs.  …”
Get full text

Formula Student Race Car Chassis Design and Analysis by Yiğit Alp Oymak, Erol Feyzullahoğlu

“…Bu çalışmada SolidWorks 2018 programı ile Formula Student yarış aracının şasi sistemi tasarım kriterleri dikkate alınarak yeniden tasarlanmıştır. ANSYS 16.0 ve SolidWorks Simulation programları kullanarak şasi sisteminin mekanik zorlanmalara karşı olan dayanımlarını belirlemek için optimizas-yon çalışmaları yapılmıştır. …”
Get full text

Effects of Unidirectional In Situ Stress on Crack Propagation of a Jointed Rock Mass Subjected to Stress Wave by Zhanfeng Fan, Jianhua Cai

“…The two-dimensional finite element program (ANSYS/LS-DYNA) was applied to further simulate the crack propagation of a jointed rock mass under different in situ stresses. …”
Get full text

Investigating Reinforced Concrete Beams with Web Opening under Static and Cyclic Loads by Ali Fawzy, Arafa EL-Helloty, Mahmoud Hassan Mahmoud, Aymen Summra

“…Numerical studies were performed on ANSYS software, and the finite element results were verified through experiments. …”
Get full text

Improved Finite Beam Element Method to Analyze the Natural Vibration of Steel-Concrete Composite Truss Beam by Zhipeng Lai, Lizhong Jiang, Wangbao Zhou, Xilin Chai

“…The FBEM’s calculation results of several SCCTBs agree well with the results obtained from ANSYS. Based on the results of this study, the following conclusions can be drawn. …”
Get full text